Difference between revisions of "Diesel Version 5:CV 8"
(Reworked Description) |
|||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{:CV_8}} |
| − | | | + | {| class="wikitable" |
| − | | | + | |+WOWSound Version 5 |
| − | | | + | !Value |
| − | | | + | !Macro/Operation |
| − | + | |- | |
| − | + | |2 | |
| − | + | |Factory Reset | |
| − | + | |- | |
| − | + | |3 | |
| − | + | |Reset Sound Button Mappings | |
| − | + | |- | |
| − | + | |4 | |
| + | |Reset all [[Diesel Version 5:WOWDiesel Standard CV's|NMRA CV's]] (1-256) | ||
| + | |- | ||
| + | |5 | ||
| + | |Reset all [[Diesel Version 5:WOWDiesel Indexed CV's|Indexed CV's]] | ||
| + | |- | ||
| + | |6 | ||
| + | |Factory Reset only 128-point BEMF Table | ||
| + | |- | ||
| + | |8 | ||
| + | |Factory Reset | ||
| + | |- | ||
| + | |10 | ||
| + | |Load User Preset 1 | ||
| + | |- | ||
| + | |11 | ||
| + | |Load User Preset 2 | ||
| + | |- | ||
| + | |12 | ||
| + | |Load User Preset 3 | ||
| + | |- | ||
| + | |15 | ||
| + | |Configure F1 and F2 outputs as [https://tcsdcc.com/techsupport#ditch_lights Ditch Lights] | ||
| + | |- | ||
| + | |11+ | ||
| + | |[Reserved] | ||
| + | |} | ||
Latest revision as of 22:23, 23 July 2021
| |||||||||
NMRA CV 8 - Manufacturer ID
CV8 contains the NMRA-assigned ID number of the manufacturer of this decoder. The currently assigned manufacturer ID codes are listed under the Standards section of the NMRA Website. The use of a value not assigned by the NMRA will immediately cause the decoder to not be in conformance of the NMRA Standards.
Train Control Systems' Manufacturer ID Number is 153.
CV 8 is classified as a Read Only CV. The CV contains a value which cannot be overwritten; however, it is possible to "write" a value to this CV. Doing so may perform a "Macro" such as a Factory Reset, or other operation(s). See below some examples from TCS:
CV 8 "Macros"
CV 8 offers multiple "macro" options which allow you to quickly configure certain aspects of the decoder on the fly. Most macros will perform a sequence of operations internally within the decoder, meaning you would not need to perform each of those operations individually, and can instead use one single command. CV 8 can also be used to save and load User Presets, perform a factory reset, and more!
CV 8 Macros may be programmed on the mainline or a programming track; however, it is strongly recommended that you use a dedicated programming track when performing a factory reset so as to avoid any addressing conflicts.
Available Macros
| Value | Macro/Operation |
|---|---|
| 2 | Factory Reset (Excluding ULST) |
| 3-9 | Not Used |
| 10 | Configure F1 and F2 Ditch Lights |
| 11 | Configure Trolley Preset |
| 12 | Configure "Deluxe" Trolley Preset |
| Value | Macro/Operation |
|---|---|
| 2 | Factory Reset (Excluding ULST) |
| 3-7 | Not Used |
| 8 | Factory Reset (Excluding ULST) |
| 10 | Configure F1 and F2 Ditch Lights |
| 11 | Configure Trolley Preset |
| 12 | Configure "Deluxe" Trolley Preset |
| Value | Macro/Operation |
|---|---|
| 2 | Factory Reset (Excluding ULST) |
| 3-9 | Not Used |
| 10 | Configure F1 and F2 Ditch Lights |
| 11 | Configure Trolley Preset |
| 12 | Configure "Deluxe" Trolley Preset |
| 13 | Set Throttle Mode to "Traditional" |
| 14 | Set Throttle Mode to "Prototype" |
| Value | Macro/Operation |
|---|---|
| 2 | Factory Reset |
| 3 | Reset Sound Button Mappings |
| 4 | Reset all NMRA CV's (1-256) |
| 5 | Reset all Indexed CV's |
| 6 | Factory Reset only 128-point BEMF Table |
| 8 | Factory Reset |
| 10 | Load User Preset 1 |
| 11 | Load User Preset 2 |
| 12 | Load User Preset 3 |
| 15 | Configure F1 and F2 outputs as Ditch Lights |
| 11+ | [Reserved] |
