Difference between revisions of "LT Panel"

From Train Control Systems Documentation
Jump to navigation Jump to search
Line 52: Line 52:
 
|''Not Used''
 
|''Not Used''
 
|-
 
|-
|DCC/F (3 & 4)
+
|DCC/F (3U+AB &U+AB 4)
|The LT Panel is designed to be use with a "Layout Throttle", such as an LT-50, plugged into the front facing port with the "LT" logo.[[File:DCC-F Simplified Diagram.png|thumb|300x300px|Simplified diagram showing the electrical connection for DCC/F jumpers.]]Insert these two jumpers to pass the low power DCC signals from the Layout Throttle through to the other three LCC jacks (pins 4 & 5 of the LCC-CAN standard). Remove these jumpers to disconnect the low power DCC signals provided by the Layout Throttle.
+
|The LT Panel is designed to be use with a "Layout Throttle", such as an LT-50, plugged into the front facing port with the "LT" logo. [[File:DCC-F Simplified Diagram.png|thumb|300x300px|Simplified diagram showing the electrical connection for DCC/F jumpers.]]Insert these two jumpers to pass the low power DCC signals from the Layout Throttle through to the other three LCC jacks (pins 4 & 5 of the LCC-CAN standard). Remove these jumpers to disconnect the low power DCC signals provided by the Layout Throttle.
 
''Note: The Layout Throttle uses the [https://www.nmra.org/sites/default/files/standards/sandrp/pdf/s-9.1.2_power_station_interface.pdf NMRA S-9.1.2 Full Scale Interface]''
 
''Note: The Layout Throttle uses the [https://www.nmra.org/sites/default/files/standards/sandrp/pdf/s-9.1.2_power_station_interface.pdf NMRA S-9.1.2 Full Scale Interface]''
  

Revision as of 02:07, 6 October 2022

LT Panel
LT Panel.png
Device Information
ManufacturerTrain Control Systems
TypeFascia Panel
SKU1599
Release Date08-09-2022
Retail Price$29.95
PSUDC 15V/36W
(Not Incl.)

The LT Panel is the same fascia panel assembly which comes included with the LT-50.

This product is an expansion panel for an LCC network, such as those created and used by the CS-105 and LT-50. Use this product to expand the number of wired throttles such as the T-50 you can connect to the TCS command station, or to provide an access point and/or power for other LCC devices distributed around your layout.

The LT Panel also includes a jack you can use to connect a Power Supply to power the LCC bus. (Not Included, except with LT-50)

Included In Package

  • LT Panel board x1
  • LT Panel fascia cover plate x1
  • Fascia mounting screws x4
  • Fascia cover plate screws x2
  • Option Jumpers x3

Physical Overview

The LT Panel has a few notable physical features:

  1. Green 2-pin Track Output connector with detachable screw terminal connector
  2. 2.5mm x 5.5mm barrel jack for Power In
  3. Configuration Jumpers (see details below)
  4. Single "LT" RJ-45 jack(for LT-50 only)
  5. Three "LCC" RJ-45 jacks (1x Front: For T-50; 2x Rear for LCC Bus)
  6. Bi-color LED for "Track On"

LT Panel (2).png

Configuration Jumpers

Refer to the table below for information on the configuration jumpers available on the LT Panel:

Jumper Position Description
TERM (1) Insert this jumper to add termination to the LCC-CAN bus. An LCC-CAN bus should have exactly two terminators, with one at each end of the bus.

This jumper can (optionally) provide for one of the required terminators.

Note: In practicality, a very short (less than 10ft or 3m) LCC-CAN bus can still work reliably with one terminator.

N/A (2) Not Used
DCC/F (3U+AB &U+AB 4) The LT Panel is designed to be use with a "Layout Throttle", such as an LT-50, plugged into the front facing port with the "LT" logo.
Simplified diagram showing the electrical connection for DCC/F jumpers.
Insert these two jumpers to pass the low power DCC signals from the Layout Throttle through to the other three LCC jacks (pins 4 & 5 of the LCC-CAN standard). Remove these jumpers to disconnect the low power DCC signals provided by the Layout Throttle.

Note: The Layout Throttle uses the NMRA S-9.1.2 Full Scale Interface


DCC/F is a low-power mirror of the track output from the command station (in this case, the LT-50).

This circuit is only intended to be used to provide the signal from the LT-50 to other devices on the LCC-CAN bus. This circuit is not intended to supply signals to LCC boosters such as the B-106. This circuit must be disabled/open if another LCC device is driving the LCC-CAN pins 4 & 5 as allowed by the standard. The LT Panel is not designed to be used along with another LCC/DCC command station, such as the CS-105. In this case, an LCC Panel should be used instead.