Difference between revisions of "Diesel Version 5:CV 27"

From Train Control Systems Documentation
Jump to navigation Jump to search
m
m
 
(3 intermediate revisions by 2 users not shown)
Line 15: Line 15:
 
!Value
 
!Value
 
!Default
 
!Default
 +
!Supported by TCS
 
|-
 
|-
 
! scope="row" |0
 
! scope="row" |0
Line 20: Line 21:
 
|1
 
|1
 
|OFF
 
|OFF
 +
|NO
 
|-
 
|-
 
|-
 
|-
Line 26: Line 28:
 
|2
 
|2
 
|OFF
 
|OFF
 +
|NO
 
|-
 
|-
 
|-
 
|-
Line 32: Line 35:
 
|4
 
|4
 
|OFF
 
|OFF
 +
|NO
 
|-
 
|-
 
|-
 
|-
Line 38: Line 42:
 
|
 
|
 
|N/A
 
|N/A
 +
|
 
|-
 
|-
 
|-
 
|-
 
! scope="row" |4
 
! scope="row" |4
|Set to Enable Auto Stop in the presence of reverse polarity DC
+
|Set to Enable Auto Stop in the presence of reverse polarity (opposite current direction of travel) DC
 
|16
 
|16
 
|OFF
 
|OFF
 +
|NO
 
|-
 
|-
 
|-
 
|-
 
! scope="row" |5
 
! scope="row" |5
|Set to Enable Auto Stop in the presence forward polarity DC
+
|Set to Enable Auto Stop in the presence forward polarity (same as current direction) DC
 
|32
 
|32
 
|OFF
 
|OFF
 +
|NO
 
|-
 
|-
 
|-
 
|-
Line 56: Line 63:
 
|
 
|
 
|N/A
 
|N/A
 +
|
 
|-
 
|-
 
|-
 
|-
Line 62: Line 70:
 
|
 
|
 
|N/A
 
|N/A
 +
|
 
|-
 
|-
 
|}
 
|}
  
 
''Note If the decoder does not support a feature contained in this table, the decoder shall not allow the corresponding bit to be set improperly (i.e. the bit should always contain it’s default value).''
 
''Note If the decoder does not support a feature contained in this table, the decoder shall not allow the corresponding bit to be set improperly (i.e. the bit should always contain it’s default value).''
 +
 +
'''THIS FEATURE IS NOT CURRENTLY SUPPORTED'''
 +
[[Category:Standard CV]]
 +
[[Category:Unsupported CV]]

Latest revision as of 22:08, 9 June 2023

CV 27
Automatic Stopping Config.
Range of Values0-255
Accepted Values0-55
Default Value0

NMRA CV 27 - Decoder Automatic Stopping Configuration

This CV is used to configure which conditions on the rails will cause the decoder to automatically stop.

Bit Option Value Default Supported by TCS
0 Set to Enable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the right rail 1 OFF NO
1 Set to Enable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the left rail 2 OFF NO
2 Set to Enable Auto Stop in the presence of an Signal Controlled Influence cutout signal 4 OFF NO
3 [Reserved/Not Used] N/A
4 Set to Enable Auto Stop in the presence of reverse polarity (opposite current direction of travel) DC 16 OFF NO
5 Set to Enable Auto Stop in the presence forward polarity (same as current direction) DC 32 OFF NO
6 [Reserved/Not Used] N/A
7 [Reserved/Not Used] N/A

Note If the decoder does not support a feature contained in this table, the decoder shall not allow the corresponding bit to be set improperly (i.e. the bit should always contain it’s default value).

THIS FEATURE IS NOT CURRENTLY SUPPORTED