Difference between revisions of "Diesel Version 5:CV 27"
m (1 revision imported) |
|||
| Line 1: | Line 1: | ||
| − | == NMRA CV 27 - Decoder Automatic Stopping Configuration == | + | {{Infobox CV |
| + | |cv name= Automatic Stopping Configuration | ||
| + | |cv range=0-255 | ||
| + | |cv accepted=0-63 | ||
| + | |cv default=0 | ||
| + | }} | ||
| + | |||
| + | ==NMRA CV 27 - Decoder Automatic Stopping Configuration== | ||
Used to configure which actions will cause the decoder to automatically stop. | Used to configure which actions will cause the decoder to automatically stop. | ||
Bit 0 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the | Bit 0 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the | ||
right rail. | right rail. | ||
| + | |||
| + | {| class="wikitable" style="text-align: center;" | ||
| + | |- | ||
| + | ! scope="col"| Feature | ||
| + | ! scope="col"| Value | ||
| + | |- | ||
| + | ! scope="row"| Function 1 | ||
| + | | 1 | ||
| + | |- | ||
| + | |- | ||
| + | ! scope="row"| Function 2 | ||
| + | | 2 | ||
| + | |- | ||
| + | |- | ||
| + | ! scope="row"| Function 3 | ||
| + | | 4 | ||
| + | |- | ||
| + | |- | ||
| + | ! scope="row"| Function 4 | ||
| + | | 8 | ||
| + | |- | ||
| + | |- | ||
| + | ! scope="row"| Function 5 | ||
| + | | 16 | ||
| + | |- | ||
| + | |- | ||
| + | ! scope="row"| Function 6 | ||
| + | | 32 | ||
| + | |- | ||
| + | |- | ||
| + | ! scope="row"| Function 7 | ||
| + | | 64 | ||
| + | |- | ||
| + | |- | ||
| + | ! scope="row"| Function 8 | ||
| + | | 128 | ||
| + | |- | ||
| + | |} | ||
| + | |||
“0” = Disabled “1” = Enabled | “0” = Disabled “1” = Enabled | ||
Bit 1 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the left rail. | Bit 1 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the left rail. | ||
| Line 14: | Line 60: | ||
“0” = Disabled “1” = Enabled | “0” = Disabled “1” = Enabled | ||
Bits 6-7 = Reserved for future use. | Bits 6-7 = Reserved for future use. | ||
| − | |||
| − | |||
| − | + | *Note If the decoder does not support a feature contained in this table, it shall not allow the corresponding bit to be set improperly (i.e. the bit should always contain it’s default value). | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 22:34, 22 May 2021
| |||||||||
NMRA CV 27 - Decoder Automatic Stopping Configuration
Used to configure which actions will cause the decoder to automatically stop. Bit 0 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the right rail.
| Feature | Value |
|---|---|
| Function 1 | 1 |
| Function 2 | 2 |
| Function 3 | 4 |
| Function 4 | 8 |
| Function 5 | 16 |
| Function 6 | 32 |
| Function 7 | 64 |
| Function 8 | 128 |
“0” = Disabled “1” = Enabled Bit 1 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the left rail. “0” = Disabled “1” = Enabled Bit 2 = Enable/Disable Auto Stop in the presence of an Signal Controlled Influence cutout signal. “0” = Disabled “1” = Enabled Bit 3 = Reserved for Future Use Bit 4 = Enable/Disable Auto Stop in the presence of reverse polarity DC “0” = Disabled “1” = Enabled Bit 5 = Enable/Disable Auto Stop in the presence forward polarity DC. “0” = Disabled “1” = Enabled Bits 6-7 = Reserved for future use.
- Note If the decoder does not support a feature contained in this table, it shall not allow the corresponding bit to be set improperly (i.e. the bit should always contain it’s default value).
