Difference between revisions of "Diesel Version 5:CV 27"
Jump to navigation
Jump to search
m |
m |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 15: | Line 15: | ||
!Value | !Value | ||
!Default | !Default | ||
| + | !Supported by TCS | ||
|- | |- | ||
! scope="row" |0 | ! scope="row" |0 | ||
| Line 20: | Line 21: | ||
|1 | |1 | ||
|OFF | |OFF | ||
| + | |NO | ||
|- | |- | ||
|- | |- | ||
| Line 26: | Line 28: | ||
|2 | |2 | ||
|OFF | |OFF | ||
| + | |NO | ||
|- | |- | ||
|- | |- | ||
| Line 32: | Line 35: | ||
|4 | |4 | ||
|OFF | |OFF | ||
| + | |NO | ||
|- | |- | ||
|- | |- | ||
| Line 38: | Line 42: | ||
| | | | ||
|N/A | |N/A | ||
| + | | | ||
|- | |- | ||
|- | |- | ||
! scope="row" |4 | ! scope="row" |4 | ||
| − | |Set to Enable Auto Stop in the presence of reverse polarity DC | + | |Set to Enable Auto Stop in the presence of reverse polarity (opposite current direction of travel) DC |
|16 | |16 | ||
|OFF | |OFF | ||
| + | |NO | ||
|- | |- | ||
|- | |- | ||
! scope="row" |5 | ! scope="row" |5 | ||
| − | |Set to Enable Auto Stop in the presence forward polarity DC | + | |Set to Enable Auto Stop in the presence forward polarity (same as current direction) DC |
|32 | |32 | ||
|OFF | |OFF | ||
| + | |NO | ||
|- | |- | ||
|- | |- | ||
| Line 56: | Line 63: | ||
| | | | ||
|N/A | |N/A | ||
| + | | | ||
|- | |- | ||
|- | |- | ||
| Line 62: | Line 70: | ||
| | | | ||
|N/A | |N/A | ||
| + | | | ||
|- | |- | ||
|} | |} | ||
''Note If the decoder does not support a feature contained in this table, the decoder shall not allow the corresponding bit to be set improperly (i.e. the bit should always contain it’s default value).'' | ''Note If the decoder does not support a feature contained in this table, the decoder shall not allow the corresponding bit to be set improperly (i.e. the bit should always contain it’s default value).'' | ||
| + | |||
| + | '''THIS FEATURE IS NOT CURRENTLY SUPPORTED''' | ||
| + | [[Category:Standard CV]] | ||
| + | [[Category:Unsupported CV]] | ||
Latest revision as of 22:08, 9 June 2023
| |||||||||
NMRA CV 27 - Decoder Automatic Stopping Configuration
This CV is used to configure which conditions on the rails will cause the decoder to automatically stop.
| Bit | Option | Value | Default | Supported by TCS |
|---|---|---|---|---|
| 0 | Set to Enable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the right rail | 1 | OFF | NO |
| 1 | Set to Enable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the left rail | 2 | OFF | NO |
| 2 | Set to Enable Auto Stop in the presence of an Signal Controlled Influence cutout signal | 4 | OFF | NO |
| 3 | [Reserved/Not Used] | N/A | ||
| 4 | Set to Enable Auto Stop in the presence of reverse polarity (opposite current direction of travel) DC | 16 | OFF | NO |
| 5 | Set to Enable Auto Stop in the presence forward polarity (same as current direction) DC | 32 | OFF | NO |
| 6 | [Reserved/Not Used] | N/A | ||
| 7 | [Reserved/Not Used] | N/A |
Note If the decoder does not support a feature contained in this table, the decoder shall not allow the corresponding bit to be set improperly (i.e. the bit should always contain it’s default value).
THIS FEATURE IS NOT CURRENTLY SUPPORTED
