Diesel Version 5:CV 6 - Revision history

TCSDanM: transclude from main namespace

2021-07-21T16:54:18Z

transclude from main namespace

← Older revision		Revision as of 16:54, 21 July 2021
Line 1:		Line 1:
	{{~~Infobox CV~~		{{:CV_6}}
	~~\|cv name=Vmid (Mid Volts)~~
	~~\|cv range=0-255~~
	~~\|cv accepted=0-255~~
	~~\|cv default=0~~
	}}

	~~==NMRA CV 6 - Vmid (Mid Volts)==~~
	CV 6 specifies the voltage drive level at the middle speed step (63/126). CV 6 is used to generate a performance curve in the decoder that translate speed step values into motor voltage drive levels, and is specified as a fraction of available rectified supply voltage. CV 6 is used to "slide" the curve in one direction or another, where the value in CV 6 will adjust the curve for greater or less sensitivity in the later half of the speed curve. CV 6 should be left unmodified when setting up "speed limits" in decoders unless you are unsatisfied with the default speed curve calculation.

	~~''NOTE: CV6 will not be "in use" ''as part of the speed curve calculation'' if programmed with a value of 0 or 128''.~~

	~~CV 6 is used in conjunction with [[{{NAMESPACE}}:CV_2\|CV 2]] and [[{{NAMESPACE}}~~:~~CV_5\|CV 5]] as part of the [[{{NAMESPACE~~}}~~:3_Point_Speed_Curves_Feature\|3 Point Speed Curves feature]].~~


	~~From S-9.2.2 of the NMRA Standards and Recommended Practices:~~

	''"Vmid specifies the voltage drive level at the middle speed step. Vmid is used to generate a performance curve in the decoder that translate speed step values into motor voltage drive levels and is specified as a fraction of available rectified supply voltage. Values of 0 or 128 shall indicate that Vmid is not used in the calculation of the speed table."''

	~~[[Category:Standard CV]]~~
	~~[[Category:Motor]]~~

Dan Mycio: Added description for CV6 and some tips for programming

2021-07-02T21:56:58Z

Added description for CV6 and some tips for programming

← Older revision		Revision as of 21:56, 2 July 2021
Line 7:		Line 7:

	==NMRA CV 6 - Vmid (Mid Volts)==		==NMRA CV 6 - Vmid (Mid Volts)==
	CV6 is used in conjunction with [[{{NAMESPACE}}:CV_2\|~~CV2~~]] and [[{{NAMESPACE}}:CV_5\|~~CV5~~]] as part of the [[{{NAMESPACE}}:3_Point_Speed_Curves_Feature\|3 Point Speed Curves feature]]		CV 6 specifies the voltage drive level at the middle speed step (63/126). CV 6 is used to generate a performance curve in the decoder that translate speed step values into motor voltage drive levels, and is specified as a fraction of available rectified supply voltage. CV 6 is used to "slide" the curve in one direction or another, where the value in CV 6 will adjust the curve for greater or less sensitivity in the later half of the speed curve. CV 6 should be left unmodified when setting up "speed limits" in decoders unless you are unsatisfied with the default speed curve calculation.

			''NOTE: CV6 will not be "in use" ''as part of the speed curve calculation'' if programmed with a value of 0 or 128''.

			CV 6 is used in conjunction with [[{{NAMESPACE}}:CV_2\|CV 2]] and [[{{NAMESPACE}}:CV_5\|CV 5]] as part of the [[{{NAMESPACE}}:3_Point_Speed_Curves_Feature\|3 Point Speed Curves feature]].

Dan Mycio at 19:54, 2 April 2021

2021-04-02T19:54:55Z

← Older revision		Revision as of 19:54, 2 April 2021
Line 6:		Line 6:
	}}		}}

	== NMRA CV 6 - Vmid (Mid Volts) ==		==NMRA CV 6 - Vmid (Mid Volts)==
	Vmid specifies the voltage drive level at the middle speed step. Vmid is used to generate a performance curve in the decoder that translate speed step values into motor voltage drive levels and is specified as a fraction of available rectified supply voltage. Values of 00000000 or 00000001 shall indicate that Vmid is not used in the calculation of the speed table.<br>
	CV6 is used in conjunction with [[{{NAMESPACE}}:CV_2\|CV2]] and [[{{NAMESPACE}}:CV_5\|CV5]] as part of the [[{{NAMESPACE}}:3_Point_Speed_Curves_Feature\|3 Point Speed Curves feature]]		CV6 is used in conjunction with [[{{NAMESPACE}}:CV_2\|CV2]] and [[{{NAMESPACE}}:CV_5\|CV5]] as part of the [[{{NAMESPACE}}:3_Point_Speed_Curves_Feature\|3 Point Speed Curves feature]]


			From S-9.2.2 of the NMRA Standards and Recommended Practices:

			''"Vmid specifies the voltage drive level at the middle speed step. Vmid is used to generate a performance curve in the decoder that translate speed step values into motor voltage drive levels and is specified as a fraction of available rectified supply voltage. Values of 0 or 128 shall indicate that Vmid is not used in the calculation of the speed table."''

	[[Category:Standard CV]]		[[Category:Standard CV]]
	[[Category:Motor]]		[[Category:Motor]]

Dan Mycio at 19:48, 2 April 2021

2021-04-02T19:48:47Z

← Older revision		Revision as of 19:48, 2 April 2021
Line 1:		Line 1:
	{{Infobox		{{Infobox CV
	~~\|title = NMRA~~ CV 6		\|cv name=Vmid (Mid Volts)
	\|~~header1~~ = Vmid		\|cv range=0-255
	\|~~label2~~ = ~~Range of Values~~		\|cv accepted=0-255
	\|~~data2~~ = 0-255		\|cv default=0
	\|~~label3 = Default Value~~
	~~\|data3~~ = 0
	}}		}}

Line 11:		Line 9:
	Vmid specifies the voltage drive level at the middle speed step. Vmid is used to generate a performance curve in the decoder that translate speed step values into motor voltage drive levels and is specified as a fraction of available rectified supply voltage. Values of 00000000 or 00000001 shall indicate that Vmid is not used in the calculation of the speed table.<br>		Vmid specifies the voltage drive level at the middle speed step. Vmid is used to generate a performance curve in the decoder that translate speed step values into motor voltage drive levels and is specified as a fraction of available rectified supply voltage. Values of 00000000 or 00000001 shall indicate that Vmid is not used in the calculation of the speed table.<br>
	CV6 is used in conjunction with [[{{NAMESPACE}}:CV_2\|CV2]] and [[{{NAMESPACE}}:CV_5\|CV5]] as part of the [[{{NAMESPACE}}:3_Point_Speed_Curves_Feature\|3 Point Speed Curves feature]]		CV6 is used in conjunction with [[{{NAMESPACE}}:CV_2\|CV2]] and [[{{NAMESPACE}}:CV_5\|CV5]] as part of the [[{{NAMESPACE}}:3_Point_Speed_Curves_Feature\|3 Point Speed Curves feature]]

			[[Category:Standard CV]]
			[[Category:Motor]]

Tcsdcc: 1 revision imported

2020-12-10T19:37:27Z

1 revision imported

← Older revision	Revision as of 19:37, 10 December 2020
(No difference)

en>Tcsdcc: /* NMRA CV 6 Vmid (Mid Volts) */

2018-09-19T19:22:16Z

NMRA CV 6 Vmid (Mid Volts)

New page

{{Infobox
|title = NMRA CV 6
|header1 = Vmid
|label2 = Range of Values
|data2 = 0-255
|label3 = Default Value
|data3 = 0
}}

== NMRA CV 6 - Vmid (Mid Volts) ==
Vmid specifies the voltage drive level at the middle speed step. Vmid is used to generate a performance curve in the decoder that translate speed step values into motor voltage drive levels and is specified as a fraction of available rectified supply voltage. Values of 00000000 or 00000001 shall indicate that Vmid is not used in the calculation of the speed table.<br>
CV6 is used in conjunction with [[{{NAMESPACE}}:CV_2|CV2]] and [[{{NAMESPACE}}:CV_5|CV5]] as part of the [[{{NAMESPACE}}:3_Point_Speed_Curves_Feature|3 Point Speed Curves feature]]