Diesel Version 5:CV 1 - Revision history

TCSDanM: Replaced content with "{{:CV_1}}"

2021-07-21T16:21:28Z

Replaced content with "{{:CV_1}}"

← Older revision		Revision as of 16:21, 21 July 2021
Line 1:		Line 1:
	{{~~Infobox CV~~		{{:CV_1}}
	~~\|cv name= Short Address~~
	~~\|cv range=0-127~~
	~~\|cv accepted=1-127~~
	~~\|cv default=3~~
	}}

	~~==NMRA CV 1 - Short Address (Primary Address)==~~
	When programming a decoder address, there are two address "ranges" you can program: Two-digit "Short" addresses, and Four-digit "Long" addresses. The word "digit" refers to the number of 4-bit "nibbles" used to represent the address in binary. The word "digit" does not mean there needs to be specific numbers in your address! The address type, short or long, is select-able using [[Diesel Version 5:CV 29\|CV29]]. By default, a decoder ships in the two-digit "short" addressing format with a value of 3 in CV 1.

	~~''Note: A DCC decoder will operate out of the package on Short Address 3 with no programming required per NMRA requirement.''~~

	~~==== Short Addressing: ====~~
	The two-digit "Short" address is stored in CV1 and has a valid range of values from 1 to 127. A value higher than 127 is invalid for short addressing. If you would like to program your locomotive with an address (such as a road number) which is greater than 127, you must use a 4-digit "Long" address. Per the NMRA spec, CV1 cannot be modified on the main via operations (OPS) mode programming; therefore, you MUST use a dedicated DCC programming track to make that change.

	~~A value of 0 in CV 1 will enable "[[Diesel Version 5:CV 12\|power source conversion]]" if supported by the decoder.~~

	~~== See Also ==~~

	* [https://tcsdcc.com/techsupport#addressing Addressing]
	* [[Diesel Version 5:CV 29\|CV 29 - Configuration Data #1]]
	* [[Diesel Version 5:CV 17\|CV 17 - Extended Address (High Byte)]]
	* [[Diesel Version 5:CV 18\|CV 18 - Extended Address (Low Byte)]]
	* [[Diesel Version 5:CV 19\|CV 19 - Consist Address]]

	~~[[Category:Standard CV]]~~
	~~[[Category:Addressing]]~~

Dan Mycio at 19:23, 2 April 2021

2021-04-02T19:23:55Z

← Older revision		Revision as of 19:23, 2 April 2021
Line 6:		Line 6:
	}}		}}

	== NMRA CV 1 - Short Address (Primary Address) ==		==NMRA CV 1 - Short Address (Primary Address)==
	When programming a decoder address, there are two address "ranges" you can program: Two-digit "Short" addresses, and Four-digit "Long" addresses. The word "digit" refers to the number of 4-bit "nibbles" used to represent the address in binary. The word "digit" does not mean there needs to be specific numbers in your address! The address type, short or long, is ~~configurable~~ using CV29. By default, a decoder ships in the two-digit "short" addressing format with a value of 3. ~~A DCC decoder will operate out of the package on Address 3 with no programming required per NMRA requirement.~~		When programming a decoder address, there are two address "ranges" you can program: Two-digit "Short" addresses, and Four-digit "Long" addresses. The word "digit" refers to the number of 4-bit "nibbles" used to represent the address in binary. The word "digit" does not mean there needs to be specific numbers in your address! The address type, short or long, is select-able using [[Diesel Version 5:CV 29\|CV29]]. By default, a decoder ships in the two-digit "short" addressing format with a value of 3 in CV 1.

	Short Addressing:		''Note: A DCC decoder will operate out of the package on Short Address 3 with no programming required per NMRA requirement.''

			==== Short Addressing: ====
	The two-digit "Short" address is stored in CV1 and has a valid range of values from 1 to 127. A value higher than 127 is invalid for short addressing. If you would like to program your locomotive with an address (such as a road number) which is greater than 127, you must use a 4-digit "Long" address. Per the NMRA spec, CV1 cannot be modified on the main via operations (OPS) mode programming; therefore, you MUST use a dedicated DCC programming track to make that change.		The two-digit "Short" address is stored in CV1 and has a valid range of values from 1 to 127. A value higher than 127 is invalid for short addressing. If you would like to program your locomotive with an address (such as a road number) which is greater than 127, you must use a 4-digit "Long" address. Per the NMRA spec, CV1 cannot be modified on the main via operations (OPS) mode programming; therefore, you MUST use a dedicated DCC programming track to make that change.

	A value of 0 in CV 1 will enable "source conversion" if supported by the decoder.		A value of 0 in CV 1 will enable "[[Diesel Version 5:CV 12\|power source conversion]]" if supported by the decoder.

			== See Also ==

			* [https://tcsdcc.com/techsupport#addressing Addressing]
			* [[Diesel Version 5:CV 29\|CV 29 - Configuration Data #1]]
			* [[Diesel Version 5:CV 17\|CV 17 - Extended Address (High Byte)]]
			* [[Diesel Version 5:CV 18\|CV 18 - Extended Address (Low Byte)]]
			* [[Diesel Version 5:CV 19\|CV 19 - Consist Address]]

	[[Category:Standard CV]]		[[Category:Standard CV]]
	[[Category:Addressing]]		[[Category:Addressing]]

Dan Mycio at 19:17, 2 April 2021

2021-04-02T19:17:26Z

← Older revision		Revision as of 19:17, 2 April 2021
Line 1:		Line 1:
			{{Infobox CV
			\|cv name= Short Address
			\|cv range=0-127
			\|cv accepted=1-127
			\|cv default=3
			}}

	== NMRA CV 1 - Short Address (Primary Address) ==		== NMRA CV 1 - Short Address (Primary Address) ==
	~~CV 1 dictates what~~ the ~~short address~~ of the ~~given device~~ is. ~~Decoders ship~~ with a ~~base~~ value of 3 ~~in this CV, and allow you to begin controlling them immediately by calling up address~~ 3 ~~on your command device~~.		When programming a decoder address, there are two address "ranges" you can program: Two-digit "Short" addresses, and Four-digit "Long" addresses. The word "digit" refers to the number of 4-bit "nibbles" used to represent the address in binary. The word "digit" does not mean there needs to be specific numbers in your address! The address type, short or long, is configurable using CV29. By default, a decoder ships in the two-digit "short" addressing format with a value of 3. A DCC decoder will operate out of the package on Address 3 with no programming required per NMRA requirement.

	~~{{Infobox~~		Short Addressing:
	~~\|title =~~ NMRA ~~CV 1~~		The two-digit "Short" address is stored in CV1 and has a valid range of values from 1 to 127. A value higher than 127 is invalid for short addressing. If you would like to program your locomotive with an address (such as a road number) which is greater than 127, you must use a 4-digit "Long" address. Per the NMRA spec, CV1 cannot be modified on the main via operations (OPS) mode programming; therefore, you MUST use a dedicated DCC programming track to make that change.
	~~\|header1 = Base Functionality~~
	~~\|label2 = Range~~ of ~~Values~~		A value of 0 in CV 1 will enable "source conversion" if supported by the decoder.
	~~\|data2 =~~ 1~~-127~~
	~~\|label3 = Accepted Values~~		[[Category:Standard CV]]
	~~\|data3 = Any~~		[[Category:Addressing]]
	}}

Tcsdcc: 1 revision imported

2020-12-10T19:36:13Z

1 revision imported

← Older revision	Revision as of 19:36, 10 December 2020
(No difference)

en>Dan Mycio: Changed "range of values" from 0-255 to 1-127

2018-10-02T16:26:42Z

Changed "range of values" from 0-255 to 1-127

New page

== NMRA CV 1 - Short Address (Primary Address) ==
CV 1 dictates what the short address of the given device is. Decoders ship with a base value of 3 in this CV, and allow you to begin controlling them immediately by calling up address 3 on your command device.

{{Infobox
|title = NMRA CV 1
|header1 = Base Functionality
|label2 = Range of Values
|data2 = 1-127
|label3 = Accepted Values
|data3 = Any
}}